How To Change Oil On Honda Pressure Water Gcv160
Maintenance Schedule
Before each use: Check the air cleaner and the oil level.
First month or 5 hours of operation: Change the oil.
Every flavour or 25 hours: Clean the air cleaner
Every season or fifty hours: Modify the oil, check the spark plug, and inspect the flywheel brake pad.
Every 100 hours: Bank check the blade, brake, clutch, and spark arrester (if equipped.)
Every 200 hours: Supersede the air cleaner and spark plug.
Every 2 years: Check the fuel line for cracks and damage.
Honda recommends bringing this motor to a service center for the post-obit maintenance.
Every 100 hours: Check the valve clearance, fuel tank, and fuel filter.
Every 150 hours: Accommodate the idle speed.
Fuel
This engine is designed to use standard automotive unleaded with an octane rating of 86 or higher and no more than 10% ethanol (E10) or 5% methanol. The tank should not exist filled past the base of the filler neck. When closing the tank, twist the fuel cap until it makes an audible click. Always motility the equipment at least x anxiety (iii meters) abroad from the fueling location before starting to prevent the ignition of gas fumes.
Oil
Honda recommends 10W30, only 5W30 tin also be used, or SAE 30 so long equally temperatures are above 50 degrees F (10 degrees C.) This oil should meet API standard SJ or afterwards.
To check the oil, remove the dipstick from the filler neck, wipe off any oil, and reinsert it without screwing information technology dorsum into the neck. Remove the dipstick over again and look for oil. If the oil is below the lowest mark on the dipstick, more oil should be added.
To alter the oil, make sure the fuel valve is set to "OFF," remove the dipstick, and tilt the engine, letting the oil drain into a container for recycling. Once the oil has tuckered, tilt the engine back so that it's level and add together fresh oil. Reinstall the dipstick.
Air Cleaner
The filter can be accessed past pushing in on the tabs at the height of the encompass and swinging the cover downward.
To clean the filter element, tap it against a hard surface to loosen dirt or blow it out using compressed air with a force per unit area of 30 psi or less. Wipe out whatever dirt inside the cover before reinstalling the filter.
Spark Plug
Notation that there are two spark plugs specified for this engine. The one yous'll need depends on whether or not it's beingness used to power a pressure washer.
To access the spark plug, remove the spark plug cap and unscrew the plug using a spark plug wrench. The plug should be replaced if it'south fouled, has a croaky insulator or worn electrode or is otherwise damaged.
The spark plug gap should be prepare to betwixt 0.028 and 0.030 inches (0.70 to 0.lxxx mm.)
When installing, make sure the sealing washer is at the base of operations of the threads. The plug should offset exist screwed in past hand to forbid cross-threading, then tightened down with the plug wrench. Turn the plug 1/8-ane/4 plough after information technology seats if information technology has been used. New plugs should be turned 1/ii turn after seating to compress the washer.
Flywheel Restriction Inspection
To access the restriction, start past removing the three flange nuts on the top of the recoil starter. Remove the recoil starter from the engine.
Adjacent, slide the fuel tank off of the engine without disconnecting the fuel line. If there's fuel in the tank, set it next to the engine while keeping it level.
The flywheel brake is located next to the flywheel and has a big spring fastened to it. The brake shoe volition need to exist replaced if information technology's less than 3 mm thick. Honda recommends having this washed at a service centre.
Reinstall the tank and recoil starter in opposite society, making sure there are still three spacers on the studs that laissez passer through the tank to agree everything in the right position.
Spark Arrester
The arrester is an optional slice of equipment, but it can be added to whatever GCV160 to run across local burn regulations.
To access it, remove the three 6mm bolts holding on the muffler protector, then remove the screw holding the arrester inside the muffler. Use a wire brush to remove any carbon buildup. The spark arrester should be replaced if it has any holes or cracks. Reinstall in contrary order.
Getting Parts for Your GCV 160
When you need parts for Honda small engines, visit www.hondalawnparts.com. We're a certified Honda dealer, and we can transport OEM replacements for annihilation on your motor to whatever accost in the U.S. and Canada.
Source: https://blog.hondalawnparts.com/honda-gcv-160-maintenance-guide/
Posted by: ammonsmucithe.blogspot.com
0 Response to "How To Change Oil On Honda Pressure Water Gcv160"
Post a Comment